A buffer amplifier (sometimes simply called a buffer) is one that provides electrical impedance transformation from one circuit to another, with the aim of preventing the signal source from being affected by whatever currents (or voltages, for a current buffer) that the load may be produced with. An important aspect of the utility of the MOSFET in this application comes from the fact that the control signal is well isolated from the resistor terminals. AVoltage-Controlled Attenuator As one example, the circuit in Fig. 4.8(a), shown conceptually in Fig. 4.8(b), represents a voltage.

• Mosfet As Resistor Calculator
• Mosfet As Resistor Color
• Mosfet Act As Resistor

A buffer amplifier (sometimes simply called a buffer) is one that provides electrical impedance transformation from one circuit to another, with the aim of preventing the signal source from being affected by whatever currents (or voltages, for a current buffer) that the load may be produced with. The signal is 'buffered from' load currents. Two main types of buffer exist: the voltage buffer and the current buffer.

Voltage buffer[edit]

A voltage buffer amplifier is used to transfer a voltage from a first circuit, having a high output impedance level, to a second circuit with a low input impedance level. The interposed buffer amplifier prevents the second circuit from loading the first circuit unacceptably and interfering with its desired operation, since without the voltage buffer the voltage of the second circuit is influenced by output impedance of the first circuit (as it is larger than the input impedance of the second circuit). In the ideal voltage buffer in the diagram, the input resistance is infinite and the output resistance zero (output impedance of an ideal voltage source is zero). Other properties of the ideal buffer are: perfect linearity, regardless of signal amplitudes; and instant output response, regardless of the speed of the input signal.

If the voltage is transferred unchanged (the voltage gainA_v is 1), the amplifier is a unity gain buffer; also known as a voltage follower because the output voltage follows or tracks the input voltage. Although the voltage gain of a voltage buffer amplifier may be (approximately) unity, it usually provides considerable current gain and thus power gain. However, it is commonplace to say that it has a gain of 1 (or the equivalent 0 dB), referring to the voltage gain.

As an example, consider a Thévenin source (voltage V_A, series resistance R_A) driving a resistor load R_L. Because of voltage division (also referred to as 'loading') the voltage across the load is only V_A R_L / ( R_L + R_A ). However, if the Thévenin source drives a unity gain buffer such as that in Figure 1 (top, with unity gain), the voltage input to the amplifier is V_A, and with no voltage division because the amplifier input resistance is infinite. At the output the dependent voltage source delivers voltage A_v V_A = V_A to the load, again without voltage division because the output resistance of the buffer is zero. A Thévenin equivalent circuit of the combined original Thévenin source and the buffer is an ideal voltage source V_A with zero Thévenin resistance.

Current buffer[edit]

Typically a current buffer amplifier is used to transfer a current from a first circuit, having a low output impedance level, to a second circuit with a high input impedance level.^[1] The interposed buffer amplifier prevents the second circuit from loading the first circuit's current unacceptably and interfering with its desired operation. In the ideal current buffer in the diagram, the output impedance is infinite (an ideal current source) and the input impedance is zero (a short circuit). Again, other properties of the ideal buffer are: perfect linearity, regardless of signal amplitudes; and instant output response, regardless of the speed of the input signal.

For a current buffer, if the current is transferred unchanged (the current gainβ_i is 1), the amplifier is again a unity gain buffer; this time known as a current follower because the output current follows or tracks the input current.

As an example, consider a Norton source (current I_A, parallel resistance R_A) driving a resistor load R_L. Because of current division (also referred to as 'loading') the current delivered to the load is only I_A R_A / ( R_L + R_A ). However, if the Norton source drives a unity gain buffer such as that in Figure 1 (bottom, with unity gain), the current input to the amplifier is I_A, with no current division because the amplifier input resistance is zero. At the output the dependent current source delivers current β_i I_A = I_A to the load, again without current division because the output resistance of the buffer is infinite. A Norton equivalent circuit of the combined original Norton source and the buffer is an ideal current source I_A with infinite Norton resistance.

Voltage buffer examples[edit]

Mosfet As Resistor Calculator

Op-amp implementation[edit]

A unity gain buffer amplifier may be constructed by applying a full series negative feedback (Fig. 2) to an op-amp simply by connecting its output to its inverting input, and connecting the signal source to the non-inverting input (Fig. 3). Unity gain here implies a voltage gain of one (i.e. 0 dB), but significant current gain is expected. In this configuration, the entire output voltage (β = 1 in Fig. 2) is fed back into the inverting input. The difference between the non-inverting input voltage and the inverting input voltage is amplified by the op-amp. This connection forces the op-amp to adjust its output voltage simply equal to the input voltage (V_out follows V_in so the circuit is named op-amp voltage follower).

The impedance of this circuit does not come from any change in voltage, but from the input and output impedances of the op-amp. The input impedance of the op-amp is very high (1 MΩ to 10 TΩ), meaning that the input of the op-amp does not load down the source and draws only minimal current from it. Because the output impedance of the op-amp is very low, it drives the load as if it were a perfect voltage source. Both the connections to and from the buffer are therefore bridging connections, which reduce power consumption in the source, distortion from overloading, crosstalk and other electromagnetic interference.

Single-transistor circuits[edit]

Other unity gain buffer amplifiers include the bipolar junction transistor in common-collector configuration (called an emitter follower because the emitter voltage follows the base voltage, or a voltage follower because the output voltage follows the input voltage); the field effect transistor in common-drain configuration (called a source follower because the source voltage follows the gate voltage or, again, a voltage follower because the output voltage follows the input voltage); or similar configurations using vacuum tubes (cathode follower), or other active devices. All such amplifiers actually have a gain of slightly less than unity, but the difference is usually small and unimportant.

Impedance transformation using the bipolar voltage follower[edit]

Using the small-signal circuit in Figure 4, the impedance seen looking into the circuit is

${\displaystyle R_{\mathrm{i}\mathrm{n}}=\frac{v_x}{i_x}=r_{\pi }+(\beta +1)(r_{\mathrm{O}}||R_{\mathrm{L}})}$

(The analysis uses the relation g_mr_π = (I_C /V_T) (V_T /I_B) = β, which follows from the evaluation of these parameters in terms of the bias currents.) Assuming the usual case where r_O >> R_L, the impedance looking into the buffer is larger than the load R_L without the buffer by a factor of (β + 1), which is substantial because β is large. The impedance is increased even more by the added r_π, but often r_π << (β + 1) R_L, so the addition does not make much difference

Impedance transformation using the MOSFET voltage follower[edit]

Using the small-signal circuit in Figure 5, the impedance seen looking into the circuit is no longer R_L but instead is infinite (at low frequencies) because the MOSFET draws no current.

As frequency is increased, the parasitic capacitances of the transistors come into play and the transformed input impedance drops with frequency.

Chart of single-transistor amplifiers[edit]

Some configurations of single-transistor amplifier can be used as a buffer to isolate the driver from the load. For most digital applications, an NMOS voltage follower (common drain) is the preferred configuration.^[dubious] These amplifiers have high input impedance, which means that the digital system will not need to supply a large current.

Mosfet As Resistor Color

Amplifier type	MOSFET (NMOS)	BJT (npn)	Notes
Common gate/base	Typically used for current buffering
Common drain/collector	Voltage gain is close to unity, used for voltage buffering.

Logic buffer amplifiers[edit]

A non-linear buffer amplifier is sometimes used in digital circuits where a high current is required, perhaps for driving more gates than the normal fan-out of the logic family used, or for driving displays, or long wires, or other difficult loads. It is common for a single package to contain several discrete buffer amplifiers. For example, a hex buffer is a single package containing 6 discrete buffer amplifiers^[dubious], and an octal buffer is a single package containing 8 discrete buffer amplifiers. The terms inverting buffer and non-inverting buffer effectively correspond with high-current capability single-input NOR or OR gates respectively.

Speaker array amplifiers[edit]

The majority of amplifiers used to drive large speaker arrays, such as those used for rock concerts, are amplifiers with 26-36dB voltage gain capable of high amounts of current into low impedance speaker arrays where the speakers are wired in parallel.

Driven guards[edit]

Mosfet Act As Resistor

A driven guard utilizes a voltage buffer to protect a very high impedance signal line by surrounding the line with a shield driven by a buffer to the same voltage as the line, the close voltage matching of the buffer prevents the shield from leaking significant current into the high impedance line while the low impedance of the shield can absorb any stray currents that could affect the signal line.

Current buffer examples[edit]

Simple unity gain buffer amplifiers include the bipolar junction transistor in common-base configuration, or the MOSFET in common-gate configuration (called a current follower because the output current follows the input current). The current gain of a current buffer amplifier is (approximately) unity.

Single-transistor circuits[edit]

Figure 6 shows a bipolar current buffer biased with a current source (designated I_E for DC emitter current) and driving another DC current source as active load (designated I_C for DC collector current). The AC input signal current i_in is applied to the emitter node of the transistor by an AC Norton current source with Norton resistance R_S. The AC output current i_out is delivered by the buffer via a large coupling capacitor to load R_L. This coupling capacitor is large enough to be a short circuit at frequencies of interest.

Because the transistor output resistance connects input and output sides of the circuit, there is a (very small) backward voltage feedback from the output to the input so this circuit is not unilateral. In addition, for the same reason, the input resistance depends (slightly) upon the output load resistance, and the output resistance depends significantly on the input driver resistance. For more detail see the article on common base amplifier.

See also[edit]

References[edit]

1. ^'Lecture 20 - Transistor Amplifiers (II) - Other Amplifier Stages'(PDF). A current buffer takes the input current which may have a relatively small Norton resistance and replicates the current at the output port, which has a high output resistance ... Input resistance is low ... Output resistance is high ... transform a current source with medium source resistance to an equal current with high source resistance

Milwaukee Resistor has been designing and manufacturing a wide variety of standard and custom power resistors since 1944. For over 60 years our commitment to customer service, excellent quality, short lead-times and on-time delivery has allowed us to remain a leader in the highly competitive resistor market. Contact us now to experience the design flexibility and manufacturing superiority that Milwaukee Resistor is known for!

Featured Products

Applications

Dynamic Braking Dynamic braking resistors decelerate loads and are available for use with both AC variable frequency drives and DC drive applications.	Neutral Grounding Resistors Limiting the current caused by a fault when a phase of a power system unintentionally goes to ground.
Specialty Loadbanks To build a bank, submit your specifications to us.	Harmonic Filter Diverting excess power being generated by converting electrical energy into heat.